http://classicflyrodforum.com/topic/26189/t/Making-brass-spool-arbors.html en-us Copyright 2006, Kickapps feeds@kickapps.com (FeedMaster) webmaster@kickapps.com (WebMaster) Tue, 14 Jul 2009 05:19:08 GMT Tue, 11 Aug 2009 13:33:15 GMT Kickapps Feeds 1.0 http://blogs.law.harvard.edu/tech/rss 60 {pics-1.1 "http://www.icra.org/ratingsv02.html" l gen true for "http://kickapps.com" r (nz 1 vz 1 lz 1 oz 1 cz 1 ) "http://www.rsac.org/ratingsv01.html" l gen true for "http://kickapps.com" r (n 0 s 0 v 0 l 0 )) Search Domain q http://kickapps.com/search/direct/ http://classicflyrodforum.com/reply/149699/t/Making-brass-spool-arbors.html#reply-149699 feeds@kickapps.com (Eebarral) http://classicflyrodforum.com/sreply/149699 Tue, 11 Aug 2009 13:33:12 PST http://classicflyrodforum.com/reply/147246/t/Making-brass-spool-arbors.html#reply-147246 Yes you have it, say three short pressed pins on each side into the arbor to locate and keep rigid while you silver solder, trick is drilling and getting the right fit. Or could be homemade nickel silver screws then turn the heads off after s soldering. You could alternatively peen a shoulder over trapping the side plates, then turn clean after silver soldering. Be sure to use high sillver content silver solder, Easyflo no.2, hope this helps. By the way just got a digital camera and started making little youtubes, see http://richardkell.livejournal.com/ ]]> feeds@kickapps.com (richard kell handmade reels) http://classicflyrodforum.com/sreply/147246 Sun, 19 Jul 2009 05:29:16 PST http://classicflyrodforum.com/reply/147006/t/Making-brass-spool-arbors.html#reply-147006 Your input is very much appreciated. I recently ordered some material but didn't get any thinner than .096. I wasn't sure how rigid it would be. In a perfect world I would think the sides would be pressed and formed. Could you please elaborate on what you meant by "pin and silver solder". Do you mean to run 3 or 4 pins through the side and into the arbor material behind it, as to prevent the side from turning on the shaft?

Thanks,
Jason
]]> feeds@kickapps.com (jason) http://classicflyrodforum.com/sreply/147006 Thu, 16 Jul 2009 20:29:57 PST http://classicflyrodforum.com/reply/146980/t/Making-brass-spool-arbors.html#reply-146980 feeds@kickapps.com (richard kell handmade reels) http://classicflyrodforum.com/sreply/146980 Thu, 16 Jul 2009 17:52:17 PST http://classicflyrodforum.com/reply/146914/t/Making-brass-spool-arbors.html#reply-146914 http://www.sheffieldsupply.com/
]]> feeds@kickapps.com (jason) http://classicflyrodforum.com/sreply/146914 Thu, 16 Jul 2009 10:39:56 PST http://classicflyrodforum.com/reply/146902/t/Making-brass-spool-arbors.html#reply-146902
thx,
je ]]> feeds@kickapps.com (drbaits) http://classicflyrodforum.com/sreply/146902 Thu, 16 Jul 2009 08:31:12 PST http://classicflyrodforum.com/reply/146732/t/Making-brass-spool-arbors.html#reply-146732
A few suggestions:
1. The least expensive way ($100 or less) would be to purchase an inexpensive arbor press and make a tool to press the sides onto the spindle.
2. A little more expensive ($200 -$300), purchase a hydraulic press and make tool to hold the spindle and a tool to press the sides onto the spindle.
3. Suggest you leave a little extra material on the spindle so you can true / test the spool assembly in the lathe. Hope that helps some.

-Holireels- ]]> feeds@kickapps.com (Holireels) http://classicflyrodforum.com/sreply/146732 Tue, 14 Jul 2009 22:47:20 PST http://classicflyrodforum.com/reply/146607/t/Making-brass-spool-arbors.html#reply-146607 ]]> feeds@kickapps.com (jason) http://classicflyrodforum.com/sreply/146607 Tue, 14 Jul 2009 05:26:49 PST http://classicflyrodforum.com/topic/26189/t/Making-brass-spool-arbors.html
Thanks,
JD
]]> feeds@kickapps.com (jason) http://classicflyrodforum.com/topic/26189 Tue, 14 Jul 2009 05:19:08 PST