Cutting bamboo
Moderators: czkid, Whitefish Press
-
- Guide
- Posts: 153
- Joined: 06/18/12 16:17
Cutting bamboo
#1Want to make a few Bodkins out of old rod sections--- what is best way to get a clean cut on these? Have a Dremel
- fisherman911
- Bamboo Fanatic
- Posts: 1449
- Joined: 11/16/07 19:00
Re: Cutting bamboo
#2I think a small, fine tooth Gents or backsaw will give you the best result. At least that's what I use to trim the bamboo rods I build.
- Mike McGuire
- Master Guide
- Posts: 702
- Joined: 03/16/10 19:00
Re: Cutting bamboo
#3A well sharpened parting tool on a lathe makes a nice cut if that option is available to you.
Mike
Mike
A Selection of my DIY Rodmaking Tools
Re: Cutting bamboo
#5I use an 18 teeth per inch midget hacksaw! Put a ring or two of masking tape where you're going to cut!
- canerodscom
- Bamboo Fanatic
- Posts: 2865
- Joined: 02/01/04 19:00
Re: Cutting bamboo
#6A 10 or more tooth per inch bandsaw blade is my tool of choice.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Cutting bamboo
#7I use a little cheap-o pull saw that you can get in any of the big box hardware stores.
I wrap some tape around the rod section right at the point I want to cut.
The tape kind of gives me a dam to use to insure that the saw wont jump on me.
I first make a cut across each flat. That will make sure that I won't get any tear out that sometimes occurs if you just saw straight through the rod section.
That method gives me a clean cut with no splintering.
You could probably use a cut-off wheel in a dremel using the same method.
Brian
I wrap some tape around the rod section right at the point I want to cut.
The tape kind of gives me a dam to use to insure that the saw wont jump on me.
I first make a cut across each flat. That will make sure that I won't get any tear out that sometimes occurs if you just saw straight through the rod section.
That method gives me a clean cut with no splintering.
You could probably use a cut-off wheel in a dremel using the same method.
Brian
Re: Cutting bamboo
#8I use a mini cut off saw like this with great success. Makes a clean cut.
https://www.harborfreight.com/2-in-mini ... 62136.html
https://www.harborfreight.com/2-in-mini ... 62136.html
Zia Rods Brochure
www.ziarods.com
www.ziarods.com
Re: Cutting bamboo
#9tape it and cut with a dremel or foredom no sense in making mountains out of molehills
Re: Cutting bamboo
#10I use a hacksaw and small mitre saw box that I use to use small mouldings and metal edges for laminate countertops and a little sandpaper to smooth the edges.
Fred
Fred
Re: Cutting bamboo
#11Hi Guys, Isn't there a picture of Glenn Brackett using a big pair of shears cutting bamboo?
Jay Edwards
Jay Edwards
Re: Cutting bamboo
#12Not sure how he and the team cut it but Glen made the bodkin I use out of a pent section that I love. Very cool. So great project and good, good luck and if you end up with extras I bet you won’t have a hard time moving them!
Sent from my iPhone using Tapatalk Pro
Sent from my iPhone using Tapatalk Pro
-
- Bamboo Fanatic
- Posts: 1291
- Joined: 08/20/08 18:00
Re: Cutting bamboo
#13This question intrigued me. i have used a very fine blade hobbyist saw to trim tips, carefully taking a few passes on each flat until it parted. But Jay's comment reminded me of Glenn cutting tips with a pair of tin snips. I tried that with my aviation snips on a cut off piece that measured .061 and it worked beautifully. So, I'll be doing it that way now